How to Config smart track config( Dome+Bullet)on SmartPSS

  128   SmartPSS

正文介绍

How to Config Smart Track (Dome+Bullet) on SmartPSS

Description

This article will show you how to Config Smart Track (Dome+Bullet) on SmartPSS

Prerequisites

  • SmartPSS

Step by Step Instructions

After you have configured dome and fixed camera linkage, when intelligent rule of fixed camera triggers alarm, speed dome auto links to corresponding position and tracks object until the object exceeds monitor range or tracking time limit.

1. Calibration Requirement

To improve calibration success rage and accuracy, please follow:

  • Calibrate at least 4 groups, max 8 groups. 4 groups are recommended. The spots are recommended to be evenly distributed in the scene. It is not recommended to lay three or more spots on the same straight line.
  • Start from far to close by clockwise or counterclockwise direction. Point of calibration shall be even.
  • Calibrate position with obvious traits, such as cross of object corner.

2. Calibrating Camera

Step 1

Select fixed camera on device tree, right click Start Track Config.

Step 2

Associate speed dome

(1)In link speed dome area, click .

(2)Click and in dropdown list select speed dome.

(3)Set tracking config

ParameterNote
Expected magnificationLink speed dome tracking magnification.
Vertical magnification desired angleLink speed dome vertical magnification desired angle.
Tracking timeSupport setup of upper limit and lower limit. If tracking reaches min limit, current tracking can be interrupted. If a new target appears, it will track new target. If tracking reaches max limit, tracking end.
Idle timeSelect Enable, enable idle time and then when there is no target in fixed camera and reaches set time, speed dome returns to preset point.

(4)Click Save

Step 3

Calibrate fixed and dome.

(1)Click Add, a cross appears in video and meantime a record is generated.

(2)Drag cross to appropriate position.

Note:

Start from far to close by clockwise or counterclockwise direction. Point of calibration shall be even.

Calibrate position with obvious traits, such as cross of object corner.

(3) In video of speed dome, adjust speed dome position via icon below to make center of speed dome match + in fixed camera video.

IconNameNote
ZoomZoom in/out speed dome
FocusAdjust speed dome focus
IrisAdjust speed dome brightness
E-mouseElectronic mouse
Quick PositionClick this icon, select any position to monitor, then you can adjust

(4)Click to save calibration info.

(5)Repeat step 1~4, complete remaining calibration config

Note:

Each speed dome calibrates at least 4 groups, max 8 groups. 4 groups are recommended.

(6)Select preset return point.

When fixed camera video has no tracking to reach set length, speed dome can return to set preset.

(7)Click OK, to save.

Successfully calibrated fixed camera, and system feedbacks. If failed, it will inform calibration failed and please try again.

3. Achieving Smart Track (Bullet and Dome)

After you complete calibration, you can view link effect in smart track interface.

Step 1

On device tree, select IPC device, right click Smart Track.

On the left you can set PTZ,

Step 2

Execute the following operation to see link effect.

  • Manually position

Click any position in fixed camera video, link to speed dome. Speed dome will rotate to the corresponding position.

  • 3D Position

In fixed dome video pane select, speed dome will rotate to corresponding area and meantime zoom in/out.

Draw box from upper left to lower right, and zoom in when speed dome is fixed.

Draw box from lower right left to upper left, and zoom in when speed dome is fixed.

  • Manually track

Note:

In order to make sure that manual track is accurate, you can click at the upper right corner of Smart Track interface to disable auto track, and the icon will be displayed as after it is disabled.

  • Auto Track

For setting of tracking duration

  • Return to Preset

Enable idle return to preset during calibration, in any status, if there is no target triggering track in the bullet picture during the period, then the speed dome picture will return to the designated preset.

LEAVE A COMMENT